Results 1 to 8 of 8

Thread: NA ('91) Parts For Sale

  1. #1
    Chassis Designer
    Join Date
    May 2008
    Location
    Providence Village, TX
    Posts
    148

    Default NA ('91) Parts For Sale

    Car is a '91 and is pretty basic, nothing fancy.

    Here is what I have removed from the car so far and more will come.

    SPARE TIRE/WHEEL $20


    A/C CONDENSER, LINES, DRYER, AND COMPRESSOR (not sure if it works) $50



    DRIVER'S AND PASS WINDOWS $40 EACH



    DRIVER'S 1/4 WINDOW $30



    DRIVER'S AND PASS MANUAL WINDOW MECHANICS $15 EACH



    DRIVER AND PASS SEAT BELT AND LATCH $10 EACH



    VERY NICE CONV TOP FRAME $75



    AIR BAG SENSORS (good) $40 for all



    '91 1.6 WITH LOW COMPRESSION BUT IN RUNNING ORDER w/flywheel and clutch and everything bolted to it $500









    If motor sells then I am installing a Mitsubishi 4G63 turbo motor with a Toyota trans but if it doesnt then I am building a Spec Miata out of the car. This will determin what else comes off of the car.

  2. #2

    Default

    Its funny, I have most of these parts sitting in my garage also from lightening mine.
    John O.
    94R

  3. #3

    Default

    I need a cup holder...
    do you want to sell one??

  4. #4

    Default

    Where is Providence Village? I might be interested in one or both of the window mechanisms. Mainly passenger, but I'll have to go over my car and find out.
    09 Lexus RX350
    .... no Miata

  5. #5
    Chassis Designer
    Join Date
    May 2008
    Location
    Providence Village, TX
    Posts
    148

    Default

    I dont have a cup holder, sorry.

    Providence is east of Denton on Hwy 380

    MAP

    I have a shop there in Cross Roads. All of the are is new and really doesnt show up on the photo maps yet. Either way, I am not far from Frisco, McKinney, Denton, The Colony. I can ship items or meet people around town sometimes. I am all over the place as a field technician.

  6. #6

    Default

    I busted my left turn signal today.. have one of those?

  7. #7

    Default

    I need a cheap bumper and hood.
    TXMC: Drinkin, shootin, racin!

  8. #8
    Chassis Designer
    Join Date
    May 2008
    Location
    Providence Village, TX
    Posts
    148

    Default

    I am keeping the car so I need the turn signals. I am building a race car project. As it says in my original post, "If motor sells then I am installing a Mitsubishi 4G63 turbo motor with a Toyota trans but if it doesnt then I am building a Spec Miata out of the car. This will determin what else comes off of the car." If I sell the motor I will have another block, a tranny, driver shaft, and other engine related items for sale. No matter what set-up I end up going with I will be replacing the rear end at some point so the '91 rear end and axles will be for sale eventually.

Similar Threads

  1. parts for sale
    By driftdevil in forum dfwMiata.com Classifieds
    Replies: 24
    Last Post: 09-08-2008, 09:41 PM
  2. Parts for sale @ trackdogracing
    By johnwag in forum dfwMiata.com Classifieds
    Replies: 25
    Last Post: 02-22-2008, 07:22 PM
  3. car parts for sale
    By Billy Blaze in forum dfwMiata.com Classifieds
    Replies: 41
    Last Post: 01-20-2008, 11:28 AM
  4. Parts for sale off wrecked '93
    By johnwag in forum dfwMiata.com Classifieds
    Replies: 24
    Last Post: 10-21-2007, 10:48 PM
  5. Lots Of Parts For Sale
    By jonyellow911 in forum dfwMiata.com Classifieds
    Replies: 4
    Last Post: 09-19-2007, 09:16 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •