Results 1 to 8 of 8

Thread: Cosworth NC for 18.5k over on the pointy board.

  1. #1
    Driver Nails's Avatar
    Join Date
    Jan 2008
    Location
    In the land of Gar
    Posts
    3,865

    Default Cosworth NC for 18.5k over on the pointy board.

    No affiliation just thought this was a good deal.

    Cosworth Supercharged NC with built engine and mods
    Base 2006, ~32K, JIC's, 16x8 rims, Mazdaspeed strut and rear chassis brace, IL motorsports full brace package, added factory cruise. Galaxy Grey in 9.7+ condition. No damage or door dings. Engine was just built with 2010 forged crank, Cosworth forged pistons and rods, Cosworth rod bearings. Piston tops ceramic coated, piston sides and all bearings coated, ACT clutch upgrade, EXEDE engine management, Goodwin mid-pipe. SC has about 10K on it. Pulled 210 RWHP on dyno yesterday, equivalent to 230+ RWHP on a Dynojet.

    Going to pick it up in Charlotte this weekend from the shop. No track time after I boosted it a year ago. Maybe 100+ miles at Hallet and Omaha of HPDE driving on the car over the last 4 years, no racing, no AX miles. A lot of highway miles running between KC and the SouthEast. Also have a set of new Hankook RS-2's that I bought 225/45/16's. Existing set of T1-R's are 60% worn.


    Near the ultimate performance NC, perfectly streetable. The exhaust header and muffler is factory, so another 20 HP is easily within reach with a header and full exhaust. Raising the rev limiter would also give another 20HP. Adult driven, non-smoker, garaged. 5speed,cloth,no LSD. Top was replaced under warranty Feb 2009.


    $18,500

    __________________
    I don't care what you say, my anecdotal evidence agrees with my reality

  2. #2

    Default

    Cool! Would be interesting to have two Cosworth NCs in the area. Will make Keller's that much more interesting. :)
    '90 "LE" available for purchase soon
    2008.5 CWP MS3: JBR 70d trilogy engine mounts, short throw shifter & shift plate bushings; AST 4100 w/ 400lb springs f/r; JRZ camber plates

  3. #3

    Default

    How can you do this much to it and not add the LSD?
    Polished Turd Racing

    Mick wrote: "I think Jerrett is the best autocrosser I have ever seen naked."

  4. #4
    Driver Nails's Avatar
    Join Date
    Jan 2008
    Location
    In the land of Gar
    Posts
    3,865

    Default

    It's a base model. To add one DIY would cost over a grand.

  5. #5

    Default

    Lack of LSD knocks this down a few notches. And methinks it's a bit pricey at 18.5
    Speed

    ––––––––––––––––?? ?––––––––––––––––? ??––––
    Don't look...there's nothing down here for you!

  6. #6

    Default

    the LSD would be well worth it even for the money... and look at the mods he has... he has the money....
    Cory
    2006 Mazda MX-5 GT (SOLD)
    ​1999 Mazda Miata (FOR SALE)
    2004 Chevrolet Z06/Z16
    2013 Kawasaki Ninja 650

  7. #7
    Driver Nails's Avatar
    Join Date
    Jan 2008
    Location
    In the land of Gar
    Posts
    3,865

    Default

    Agreed I would definitely add the LSD next. He got his internals and rebuild courtesy of Cosworth as part of the warranty on the superchargers for early adopters. Because of those fresh forged cosworth internals; it's not too pricey to me. But I would get the LSD and take it to Joe at DP Tune and lose the exede if it were mine.

  8. #8

    Default

    Hey I just looked at the seller and it's the same guy I bought my hardtop from in Kansas City...
    He was really nice, and that's not a bad price with all the mods (especially all the Cosworth parts which can be really pricey) and the JIC's
    If I were in the market I'd definitely consider it...
    Cory
    2006 Mazda MX-5 GT (SOLD)
    ​1999 Mazda Miata (FOR SALE)
    2004 Chevrolet Z06/Z16
    2013 Kawasaki Ninja 650

Similar Threads

  1. May get banned from pointy board...
    By CarCar in forum Bull
    Replies: 7
    Last Post: 11-06-2009, 10:58 AM
  2. Why is it called the POINTY Board
    By Ataim in forum Bull
    Replies: 44
    Last Post: 08-16-2007, 05:31 PM
  3. Pointy Board is going down
    By POS Racing in forum Bull
    Replies: 19
    Last Post: 05-20-2005, 12:16 PM
  4. First dibs to the Pointy Board?
    By Titus in forum Bull
    Replies: 9
    Last Post: 02-01-2005, 01:58 PM
  5. Pointy Board down...
    By Miatamaniac92 in forum Bull
    Replies: 29
    Last Post: 03-26-2004, 05:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •