I am looking for the part the seat belt clips into on the driver and passenger side from a 90-92.
Printable View
I am looking for the part the seat belt clips into on the driver and passenger side from a 90-92.
New seats for the silver miata?
I have a pair of '92 black seat belts, but not the receivers. If they will help, PM me.
For the silver on if I keep it. It is really tough to fit in it with a helmet and hardtop. Looking like I might need to sell it.
:clap:Quote:
Originally Posted by ken o
I keep hitting my head on the roof.
How many do you want??????
Could you get a different seat/seat rails or take some padding out of the seat bottom?Quote:
Originally Posted by ken o
That sounds like what he plans on doing. Getting the early seatbelt receiver allows him to have the seatbelt connect to the transmission tunnel so he can replace the OEM seat.Quote:
Originally Posted by CosmosMpower
He's already done a major foam-ectomy on the seat. I sat in it at the SCCA event last week and that was the first question I asked (about his helmet clearing the hard top).Quote:
Originally Posted by CosmosMpower
I have 2 of them...
want em still?
yeah those connectors.... i got 2
I need a driver side and a passenger side. I am going to try an Ultrashield seat from Gary at TRD. I will need the receivers to bolt to the tunnel as I will lose the receivers on the seats. Where are you located and how much do you want?
I also need someone to make and weld a bracket on to the rollbar for a harness ring. Any suggestions?
Thanks for the replies.
You really don't need tabs. Wrap them around the bar and use the same slotted plates as you use on the lap belts. It works just as well. My SSB/SM Miata was done that way for six years without any problems.Quote:
Originally Posted by ken o
BTW, I have several sets of the seat belt receivers for the tunnel.
Merv
Thanks Merv. The roll bar does not have a harness bar. The straps would wrap around the diagonal on the roll bar. It would put the harness off center. Wouldn't this cause the seat to be pulled off center? On the other Miata it had a harness bar and the harness was wrapped around it, worked great.
Where can I pick up the seat belts?
You're right. That won't work. If you have no horizontal bar, where were you planing to put the tabs?Quote:
Originally Posted by ken o
I live in Springtown, but I could bring them to work (Euless).
I was going to weld the tabs to the diagonal bar. But I think I am going to sell the car. Even with the race seat I don't think I will be 2" under the bar. Looks like an E46, E36, or an STi as a track car. What a good deal on a S/C Miata? PM me.
Neither one of us can make up our minds about our miatas! :(
I know someone parting out an E36 M3 chassis. It actually has a 500 rwhp turbo setup in it right now.Quote:
Originally Posted by ken o
RX-8. :wink:Quote:
Originally Posted by ken o
Faster than an E36, loads cheaper than an E46, and a lot easier on tires than an STi. Seeing the damage that J-Fo's Evo did to my RA-1s in 6 runs at Mineral Wells made me leery about the tire budget for a nose heavy, camber-limited, Macstrut sedan. Come to think about it, that applies to the Bimmers as well. 2800 lbs > 3200+ lbs :punchout:
They're well balanced, reasonably light, have incredible brakes, and enough power to make them entertaining. You can pick up low mileage ones all day for $15-16k. Add a set of shocks and springs or your choice of coilovers, some 17" wheels and some 255/40-17 track tires, and go have fun. You know they're quick - I seem to recall running down a certain silver Miata earlier this month at MSR, and we were both on the same tires. :mrgreen:
Yes, mine has had it's share of issues (although every single one of them has been covered under warranty), but Jon's by comparison has 70k miles and hasn't had a single problem, so they're not all as fragile as mine.
The above reads like a precursor to a classified ad! ;)Quote:
Originally Posted by altiain
Good info. When I drove an RX8 I kept hitting my head on the A pillar.
I seem to recall running down a certain silver Miata earlier this month at MSR, and we were both on the same tires. :mrgreen:
Oh when I wait to for you to catch up so I could check your line? Were you on a cool down lap? It too forever for you to catch up.
Oh, was that what you were doing? How could you check my line after you fell so far behind me? ::Bleh::Quote:
Originally Posted by ken o
Nope. I like the S2000, but I've decided to keep the '8 for now.Quote:
Originally Posted by POS Racing
Your VIN # is .....Quote:
Originally Posted by altiain
Wishy-washy!