I'd suspect the special "tool" would be the tech at the Mazda dealership and the "tool" behind the parts counter and the "tool" that actually runs the joint.
The NC's owners manual says that the Oil Filter should be changed at "an authorized Mazda service center" or some such nonsense because it needs a special tool.
Anyone have any clue what they are talking about? Is the Miata's oil filter oddly shaped or needs to be tightened specially or something?
I'd suspect the special "tool" would be the tech at the Mazda dealership and the "tool" behind the parts counter and the "tool" that actually runs the joint.
I can't imagine it being hard for a DIY mechanic.
On a similar note, my wife's old 2001 Rustang had a tail light bulb go out. Owner's manual said it had to be replaced at the stealership. They wanted $50 to change it.
Got a replacement bulb for $5 at the parts store and changed it myself. It was a PITA but doable. Had to remove the taillight to get to the bulb. Dumb 'merican cars.
That's kinda what I figured. The back of my owner's manual has the P/N for the shop manuals. I will have to invest in a set one day.
Its likely due to being a cartridge filter, I know the 3's MZR uses a cartridge type filter.
I am guessing you are right wrxmr2eater. Any details on what I need to get one off and back on?
From previous (last week) experience.....the Mazda Gorilla puts them on with an 800 lb-ft torque wrench! I had to remove two of the chassis braces and grunt and groan for at least thirty minutes before I got it to budge. I could only move it about an eight of an inch each time. It went over 1/4 turn before it began to losen. It was all mangled, using the slip joint filter wrench I always use.
In other words....YOU DECIDE!!!!!
On some of the MZRs its as simple as normal drain of oil from the pan, and then when going to remove the filter, use a hey key to remove the center portion of the filter holder to drain the filter housing of oil. Once that is complete use something like a 74mm filter wrech (cup) to remove the filter housing.
I haven't been under the new Miata, this is just from working with a friends 3.
It is also almost exactly like doing my wifes Passat, but Mazda uses metal and VW seems to love pressure formed plastic
I have always used a oil change service to do this problematic job. 17 1/2 years and 155,000 miles and still going strong. I also still have all my fingers
Bobby
RED RULES!
90 Miata, 04 Rubicon, 05 Boxster
I am not sure where the oil filter is located and how much room to stick your hand/wrench into it in the NC. For my Millenia S, I have to use a "cap" type oil filter wrench with an enxtension and my socket wrench to get to the filter. It is not hard at all if you have what is needed. It is just that the filter is hard to get to w/o some kind tool. I would rather invest in the tools and leave the "stealership" out of the equation, unless you are comfortable having a high school kid changing oil on you new car!
Gabriel
OK, by "hey key", I am sure you mean "hex key" as in a Stanley wrench, and I am going to guess on my Miata it is a torx head. Those things are everywhere on the NC. I guess I need to get a set. Thanks for the help. I am going to do the oil change in a month, and if extra tools are needed I would like to get them now.
I already have a pretty full range of tools in my box. Sockets, drivers, torque wrench, Stanley wrenches, breaker bar, gear puller, torque wrench, etc. So I should have most of what I need.
It has a normal canister filter, just a bit larger than earlier Miatas. The filter is located at the rear of the block, driver's side, mounted vertically. Chassis braces ARE in the way, but easy to remove.
92 Sunny 214k, 95 Dimples, 93 James Bondo, 92 SM (Speedie Jr )
Shelley, Apex, Tigger, Max, Baby(cats), Fluffy, Spot, and Peanut (mini horses), Cinnamon & Bitsy(dawgs)
MSR #1001, SCCA #208822 Let's go racin'