Is it possible to do a couple of dyno runs on Saturday (Jan 19)?
Printable View
Is it possible to do a couple of dyno runs on Saturday (Jan 19)?
I don't see why not... have you called to see if the dyno shop is open?Quote:
Originally Posted by ken o
My friend would want to dyno his M3. I'd throw the Elise up there for fun. Where were you looking at?
That's what I am looking for. Know of one we could use?
Gearheads in Arlington does dyno's, i had my Mustang done there. It was 35 for two runs with air to fuel ratio but you have to call and set an appointment up as they are quite busy.
http://www.gearheadsperformance.com/...9/Default.aspx
Quote:
Originally Posted by ken o
Quote:
Originally Posted by CosmosMpower
Heh... I was wondering... I decided to go by what you asked instead of interpreting it. ;)Quote:
Originally Posted by ken o
Hmmm... What about the guys in Denton?
http://www.atsracing.net/
They were Miata friendly.
I give ATS a big thumbs up, Aaron is a cool guy. Someone call him in the morning and see if he could do a small dyno day.
Looks like we could 3-4 people interested as of now. I only need 1-2 runs.
I'm gonna keep an eye on this thread... if I can break away and get to Denton, I'd love to have a baseline dyno run before I start boosting things. :D
So what happened?
My 1.6 miata put down 136 rwhp and 119 wtq SAE corrected
Houston, we have a problem. I have seen 1.6s with superchargers that have dynoed less than that. I think your dyno may have been out of tune.Quote:
Originally Posted by CosmosMpower
That is pretty impressive if it is correct, since my MSM put down 154 rwhp stockQuote:
Originally Posted by CosmosMpower
Isn't that more power at the rear wheels than the factory says comes from the crank? I think they dyno was a little off. It should be closer to 90 rwhp.
+1...they were only rated at 116hp when they rolled off the assembly line.Quote:
Originally Posted by Titus
LOL I'm just screwing around, no one set anything up so we didn't go. I just wanted to see how many responses I could get to my bogus numbers. :) If you guys want to go this weekend someone should call ATS and see if they have availability to setup a dyno day.
My tired 170K mile stock 1.6 probably wouldn't even break into the 90's. I did have a 1.6L SOHC civic with a small ball bearing turbo that put down 176/173 corrected though. I always wondered why the same size Miata engine only puts down 140 s/c, must be the head design.
Yep. Before I found the darkside, my 1.6 with catback exhaust, K&N filter, and a timing bump pulled 95rwhp at ATS.Quote:
Originally Posted by jrj512
Better 95 whp than 88. :wink:
I am going to try and contact ATS today. Reply with your status, Will make it, would like to make it, you got to be f-ing kidding me. I will see what they will do for us.
I'm interested in seeing how over rated the factory HP numbers are on the RX-8!!! :(
Denton is a long way, but I'm a definite maybe. ;)
Put me down as a definite maybe, too. I am curious to see how much extra horsepower I have with the new radiator hoses. ;)
I'm interested in dyno the rx8 as well. Put me down a maybe ;)
maybe for me....what times and other info?
I should bring the Murano down so we can see what a CVT looks like on a dyno chart.
Pfff...sure, why not. If I don't have to wake up at the butt crack of dawn like every other day of the week, count me in. :D Would love base numbers anyway.
My LE with an FM cat and Borla put down 98hp at 212k miles. I haven't done a pull since I turboed it. I'll come watch if you come to Denton.
So are we doing this?
+1Quote:
Originally Posted by Miatamoto
waiting...
I'm a maybe depending on the time and day. :D